cool blog

www.certifyme.com Q:31 The default ESX service console firewall (Choose Two)? A. blocks all traffic unless specifically allowed B. is configured for medium security C. allows all traffic 220 702 unless specifically blocked D. is configured for high security Answer: A, D www.certifyme.com Q:32 ESX Service Console user authentication (Choose Two)? A. requires users to change their passwords every 6 months by default B. can use a central directory service for password checking only C. requires local accounts D. controls vCenter authentication for vSphere Client users Answer: B, C www.certifyme.com Q:33 Installing additional software in the ESX Service Console is supported in which of the following instances? A. for hardware management support B. for improved utilization of the ESX host resources C. for graphical desktop access for administrative purposes D. for enhanced virus protection Answer: A www.certifyme.com Q:34 An administrator is installing an ESX Host to boot from a SAN LUN. Which of the following two requirements are necessary when configuring the HBA in the ESX Host (Choose Two)? A. The HBA BIOS must be enabled B. The HBA must be plugged into the lowest available PCI bus and slot number C. The HBA BIOS must be disabled D. The HBA must be plugged into the highest available PCI bus and slot number Answer: A, B www.certifyme.com Q:35. An administrator is installing an ESX Host to boot from a SAN LUN. The storage array is an active/passive array. After configuring the boot LUN and installing ESX, the system does not boot properly.Which of the following could cause this issue? A. The Storage Processor 9L0-403 port specified in the BIOS configuration of the HBA is passive B. The LUN specified in the BIOS configuration of the HBA is active C. The Storage Processor port specified in the BIOS configuration of the HBA is active D. The LUN specified in the BIOS configuration of the HBA is passive Answer: A www.certifyme.com Q:36 Under which of the following conditions would an administrator consider using the Boot from SAN option for the ESX Host (Choose Two)? A. When concern exists that contention might occur between the Service Console and the VMkernel B. When using Microsoft Cluster Service C. To easily replicate the Service Console to a remote site D. In diskless hardware configurations Answer: C, D www.certifyme.com Q:37 What is the proper LUN Masking configuration for LUNs presented to an ESX Host when using the Boot from SAN option? A. The Boot LUN should be masked so that only one ESX Host can see the LUN, while the datastore LUNS should be masked so that all ESX Hosts can see the LUNs B. The Boot LUN and datastore LUNS should be masked so that all ESX Hosts can see the LUNs C. The Boot LUN should be masked so that all ESX Hosts can see the LUN, while the datastore LUNS should be masked so that 9L0-510 only one ESX Host can see the LUNs D. The Boot LUN and datastore LUNS should be masked so that only one ESX Host can see the LUNs Answer: A

www.certifyme.com Q:48 What are two reasons why a company would choose to use VMware ESXi instead of using VMware Server 2 (Choose Two)? A. The company wants to be able to patch the servers hosting their virtual machines with zero virtual machine downtime B. The company is virtualizing 220 701 several physical servers and wants a centralized management option C. The company needs to access their virtual machines remotely and VMware Server 2 does not support a remote console option D. The company needs the ability to run dual-processor virtual machines Answer: A, B www.certifyme.com Q:49 Networking policies, such as traffic shaping and security, can be configured on the following vSphere elements? A. On the physical network interface and the vSwitch B. On the port group and the physical network interface C. On the port group and the vSwitch D. On the vSwitch and the attached virtual machine Answer: C www.certifyme.com Q:50 The following connection types can all be configured on a single vSwitch? A. VMkernel, virtual machine and no Service Console port groups B. Service Console, virtual machine and VMkernel port groups C. Service Console and 2 VMkernel port groups D. Service Console and 2 virtual machine port groups Answer: B www.certifyme.com Q:51 An administrator needs to determine the current network adapter configuration for an uplink on an ESX Host. Which of the following items can be viewed from the Network Adapters section of the Configuration tab using the vSphere Client (Choose Three)? A. Wake on LAN support B. Speed and Duplex settings C. Observed IP ranges D. TCP Segmentation Offload (TSO) support E. Jumbo Frame support Answer: A, B, C www.certifyme.com Q:52 Assuming VLANs are not configured, which of the following is true about traffic from a virtual machine connected to a port group on a 220 702 vNetwork Standard Switch with no uplinks? A. Virtual machines in any port group on the virtual switch can receive the traffic B. The virtual switch will drop the packets if no uplink is present C. Virtual machines on any virtual switch on the same ESX Server can receive the traffic D. Only virtual machines in the same port group on the virtual switch can receive the traffic Answer: A www.certifyme.com Q:53 A network administrator has asked you to enable NetQueue to improve networking performance for virtual machines on an ESX Host. Where is this feature enabled (Choose Two)? A. On the physical network adapter driver B. On the virtual NIC in the virtual machine C. On the Properties tab for the virtual switch D. In the Advanced Settings for the VMkernel Answer: A, D www.certifyme.com Q:54 When configuring the vSwitch NIC teaming policy, what happens when the Notify Switches option is set to Yes? A. The virtual switch is notified when the location of a physical NIC changes B. The physical switch is notified when the location of a virtual NIC changes C. The virtual switch is notified when the physical NIC link state changes D. The physical switch is notified when the virtual NIC link state changes Answer: B www.certifyme.com Q:55 Which two statements are true about port groups and VLANs defined on a vNetwork Standard Switch (Choose Two) ? A. Only one VLAN can be specified in a port group B. Multiple VLANs can be specified in a port group C. The same VLAN cannot be specified in multiple port groups D. Multiple port groups can specify the same VLAN Answer: A, D www.certifyme.com Q:56 Which of the following describes the default behavior of uplinks added to a vNetwork Standard Switch? A. All uplinks are active B. The first uplink is active, additional uplinks are standby C. The first uplink is active, additional uplinks are unused D. Only one uplink can be attached to a virtual switch Answer: A www.certifyme.com Q:57 Traffic Shaping can be configured on the following vSphere elements (Choose Two)? A. On a vNetwork Standard Switch port group or the entire vSwitch for outbound traffic only B. On a vNetwork Distributed Switch dvPort or the entire dvPort Group for outbound traffic only C. On a vNetwork Standard 220 701 Switch port group or the entire vSwitch for inbound traffic only D. On a vNetwork Distributed Switch dvPort or the entire dvPort Group for inbound and outbound traffic Answer: A, D

The much awaited vmware certified professional on vsphere v14 vcp-410 has arrived. Now you can download the latest vcp-410 dumps from the links below http://rapidshare.com/files/289620851/VCP-410.zip When we first started 640 802 Dumps offering the VCP-410 exam questions and answers and exam simulator, we never dreamed we would be making the claims that we do now in the form of our unbelievable guarantee. Certifyme.com GUARANTEES that you will pass your VCP-410 exam on your first attempt after using one of our VCP-410 training products. That’s right, with the 100% pass rate, the exam tools that we have created for you are so good – we can’t help but guarantee your results. Known also as the VMware VMware Certified Professional on VI4 (VCP-410), this exam plays an integral role in obtaining your certification. All VMware certification exams are extremely detailed and cover many different technological areas. We designed the VCP-410 questions and answers for this very purpose, to prepare you for the unexpected. Beyond the testing center, the skills you learn and the knowledge you confirm using the VCP-410 practice exams and exam simulators will translate directly into your daily work environment. When available, take advantage of the Certifyme VCP-410 Value Pack and save time and money while developing your skills to pass your ‘VMware Certified Professional on VI4 Exam’ and grab that VMware certification. Let us help you climb that ladder of success and pass your VCP-410 now! www.certifyme.com Q:38 Which two are requirements when booting from SAN (Choose Two) ? A. The Storage Array port WWN specified in the BIOS configuration of the HBA must be passive B. The HBA should be plugged into the lowest PCI bus and slot number C. The boot LUN should only be visible to the ESX Server that is booting from it D. The boot LUN should be visible to all ESX Servers for HA failover Answer: B, C www.certifyme.com Q:39 What VMware solution is identified by hosting user desktops in a centralized manner and brokering user access? A. VMware View B. VMware vCenter Site Recovery Manager C. VMware Workstation D. VMware vCenter Orchestrator Answer: A www.certifyme.com Q:40 VMware Site Recovery Manager requires which of the following two VMware products as part of the solution (Choose Two)? A. VMware vCenter Server B. VMware HA C. VMware Data Recovery D. VMware ESX/ESXi Answer: A, D www.certifyme.com Q:41 Which 640-802 of the following VMware solutions provides developers and test engineers the equivalent of a fully-equipped datacenter with dedicated provisioning staff? A. VMware vCenter Orchestrator B. VMware vCenter Lab Manager C. VMware vCenter Capacity IQ D. VMware vCenter Lifecycle Manager Answer: B www.certifyme.com Q:42 An administrator manages a site with remote workers, business partners and third-party service providers. These users need access to corporate data and network resources while adhering to security and corporate governance regulations. Which of the following VMware solutions can provide the power and versatility of virtual machines with the security and control of centrally managed desktops? A. VMware Lifecycle Manager B. VMware Workstation C. VMware View D. VMware Server Answer: C www.certifyme.com Q:43 An administrator needs to verify the functionality of virtual machines created in several different formats prior to converting them to ESX/ESXi. Using VMware Player, which of the following virtual machines can be run directly on an administrator desktop (Choose Two)? A. Norton Ghost 10 B. Acronis True Image C. Microsoft Virtual 640 802 braindumps Server/Virtual PC D. VMware Fusion Answer: C, D

www.certifyme.com Q:58 vSphere virtual switches are configured, based on the number of physical uplinks bound, in which of the following methods? A. vSwitch with none, one or more NICs B. vSwitch with a binding to another vSwitch and one or more NICs C. vSwitch with vcp 4 bindings to a virtual machine, and HBA and the Service Console D. vSwitch with one, two or more NICs Answer: A www.certifyme.com Q:59 Which of the following two statements are true regarding vSphere virtual switch uplinks (Choose Two)? A. vSphere virtual switches must be configured with at least one uplink B. vSphere virtual switches can be configured to use the same uplink C. Multiple vSphere virtual switches cannot be configured to use the same uplink D. vSphere virtual switches do vmware vcp 4 not need to be configured with an uplink Answer: C, D www.certifyme.com Q:60 In vSphere, a bound physical NIC can be configured to transmit and receive Jumbo Frames. What is the Maximum Transmission Unit (MTU) for Jumbo Frames in vSphere? A. 9000 B. 9500 C. 5500 D. 5000 Answer: A www.certifyme.com Q:61 The vSwitch or vSwitch port group policy setting that allows a virtual machine to listen to traffic other than that which is specifically destined for the given VM is? A. MAC 640 802 Address Changes B. Promiscuous Mode C. Forged Transmits D. Traffic Shaping Answer: B

www.certifyme.com Q:62 The vSwitch or vSwitch port group policy setting that allows a virtual machine to transmit packets that contain a MAC address other vcp-410 than the address defined for the VM is? A. Promiscuous Mode B. Forged Transmits C. Traffic Shaping D. MAC Address Changes Answer: B www.certifyme.com Q:63 When an explicit failover order has not been configured on a virtual switch with multiple uplinks, what determines which uplink is used when a failover event occurs? A. The first available uplink that reports a positive Link State B. The uplink with the shortest route C. The next available uplink on the list D. The reported uptime for the surviving uplinks Answer: D www.certifyme.com Q:64 When using the Explicit Failover option for a virtual switch with multiple uplinks, ESX determines the uplink to use in a failover event by? A. a specified list B. using beacon probing to discover which uplink has the shortest route C. using the reported uptime to determine which uplink to select D. using link state tracking to see which uplinks are connected Answer: A www.certifyme.com Q:65 Beacon Probing is used in vSphere networking to? A. discover which uplink has the shortest route B. identify when an upstream link failure has occurred C. discover alternate default gateway addresses D. identify which uplink has the longest reported uptime Answer: B www.certifyme.com Q:58 vmware vcp 410 vSphere virtual switches are configured, based on the number of physical uplinks bound, in which of the following methods? A. vSwitch with none, one or more NICs B. vSwitch with a binding to another vSwitch and one or more NICs C. vSwitch with bindings to a virtual machine, and HBA and the Service Console D. vSwitch with one, two or more NICs Answer: A www.certifyme.com Q:59 Which of the following two statements are true regarding vSphere virtual switch uplinks (Choose Two)? A. vSphere virtual switches must be configured with at least one uplink B. vSphere virtual switches can be configured to use the same uplink C. Multiple vSphere virtual switches cannot be configured to use the same uplink D. vSphere virtual switches do not need to be configured with an uplink Answer: C, D www.certifyme.com Q:60 In vSphere, a bound physical NIC can be configured to transmit and receive Jumbo Frames. What is the Maximum Transmission Unit (MTU) for Jumbo Frames in vSphere? A. 9000 B. 9500 C. 5500 D. 5000 Answer: A www.certifyme.com Q:61 The vSwitch or vSwitch port group policy setting that allows a virtual machine to listen to traffic other than that which is specifically vmware vcp 4 destined for the given VM is? A. MAC Address Changes B. Promiscuous Mode C. Forged Transmits D. Traffic Shaping Answer: B

www.certifyme.com Q:65 Beacon Probing is used in vSphere networking to? A. discover which uplink has the shortest route B. identify when an upstream link failure has occurred C. discover alternate default gateway addresses D. identify which uplink Passed VCP410 has the longest reported uptime Answer: B www.certifyme.com Q:66 An administrator is building a vNetwork Distributed Switch. Which of the following describes what happens if an attempt is made to add an uplink to the switch that is in use by a vNetwork Standard Switch? A. A warning is displayed saying the uplink is currently in use and the uplink cannot be added B. The uplink is added and any virtual machines that were using the uplink lose connectivity C. The uplink and the vNetwork Standard Switch are added to the vNetwork Distributed Switch D. The uplink is added and any virtual machines that were using the uplink are added to the vNetwork Distributed Switch Answer: B www.certifyme.com Q:67 Which three are valid network load balancing policies for a vNetwork Distributed Switch (Choose Three)? A. route based on source IP hash B. route based on source MAC hash C. route based on source and destination MAC hash D. route based on explicit failover order E. route based on the originating virtual port ID Answer: B, D, E www.certifyme.com Q:68 The primary VLAN in a Private VLAN is considered? A. Promiscuous B. Isolated C. Community D. Trunked Answer: A www.certifyme.com Q:69 Passed VCP 4 Which of the following methods can be used to migrate a virtual machine from a vNetwork Standard Switch to a vNetwork Distributed Switch (Choose Two)? A. Migrate the port group containing the virtual machine from a vNetwork Standard Switch using the Migrate Virtual Machine Networking option B. Drag the virtual machine from the vNetwork Standard Switch to a vNetwork Distributed Switch dvPort group in the Configuration tab for the ESX Host C. Edit the Network Adapter settings for the virtual machine and select a dvPort group from the list D. Select the virtual machine from a list of virtual machines using the Migrate Virtual Machine Networking option Answer: C, D www.certifyme.com Q:70 A vNetwork Distributed Switch is best described as? A. A single virtual switch that aggregates existing vNetwork Standard Switches B. A distributed set of vNetwork Standard Switches that allow a virtual machine to maintain a consistent network configuration between multiple ESX Hosts C. A single virtual switch shared between multiple ESX Hosts D. A distributed set of vNetwork vcp 410 Standard Switches on individual ESX Hosts capable of forwarding traffic between hosts Answer: C

www.certifyme.com Q:76 Which is an important benefit provided by VLANs? A. higher tolerance to broken physical hardware B. improved security C. improved memory access D. higher network availability Answer: B www.certifyme.com Q:77 VCP-410 questions When creating a Service Console port, what is the purpose of the gateway device (Choose Two)? A. The gateway device is the network adapter used for the default route. B. A gateway device is required when 2 or more uplinks are using the same subnet. C. The gateway device is the Service Console port used for VMkernel networking. D. A gateway device is always required. Answer: A, B www.certifyme.com Q:78 Which of the following describe methods of adding Service Console networking to a vNetwork Distributed Switch (Choose Three)? A. A Service Console Network Adapter can be created and added to a Standalone Port B. A Service Console port can be cloned from an existing vNetwork Standard Switch C. A Service Console Network Adapter can be associated with an existing port group on a Network Distributed Switch D. A Service Console port can be migrated from an existing vNetwork Standard Switch E. A Service Console Network Adapter can be created along with a Service Console port group on the selected vNetwork Distributed Switch Answer: A, C, D www.certifyme.com Q:79 An administrator is unable to connect a vSphere Client to an ESXi Host. Which of the following options can be selected from the Direct Console to restore connectivity without disrupting running virtual machines? A. Disable the Management Network B. Restart the Management Agents C. Restore the Standard Switch D. Restart the Management Network Answer: B www.certifyme.com Q:80 An administrator is creating a vNetwork Standard Switch with Service Console and VMkernel networking. The administrator has two uplinks attached to the switch, but wants to separate the Service Console and VMkernel traffic to the two uplinks. Which of the following Load Balancing Policies will guarantee this, even if additional management or virtual machine traffic is added to the switch in the future? A. Route based on the originating port ID B. Route based on IP hash C. Use Explicit Failover D. Route based on source MAC hash Answer: C www.certifyme.com Q:71 When creating a dvPort group, which of the following port binding options assigns a port to a virtual machine the first time the virtual machine VCP-410 dumps powers on after it has been connected to the dvPort Group? A. Static Binding B. Ephemeral C. Flexible D. Dynamic Binding Answer: D www.certifyme.com Q:72 Which of the following network policies is only available with vNetwork Distributed Switches? A. Traffic Shaping Policy B. VLAN Policy C. Port Blocking Policy D. Security Policy Answer: C www.certifyme.com Q:73 Which of the following describes the functionality of traffic shaping on a vNetwork Distributed Switch? A. vNetwork Distributed Switches support Best-Effort Traffic Shaping based on Quality of Service (QoS) B. vNetwork Distributed Switches support Ingress Traffic Shaping only C. vNetwork Distributed Switches support both Ingress and Egress Traffic Shaping D. vNetwork Distributed Switches support Egress Traffic Shaping only Answer: C www.certifyme.com Q:74 Suppose you have 10000 Virtual Machines across 2 Datacenters, with approximately 5000 Virtual Machines in each Datacenter. What is the minimum number of vCenter installations and vNetwork Distributed Switches required to support this configuration (Choose Two)? A. 2 vNetwork Distributed Switches per Datacenter B. 1 vCenter Server C. 1 vNetwork Distributed Switch per Datacenter D. 2 vCenter Servers Answer: A, B www.certifyme.com Q:75 Suppose you have 10000 Virtual Machines across 2 Datacenters, with approximately 5000 Virtual Machines in each Datacenter. What is the minimum number of vCenter installations and vNetwork Distributed Switches required to support this configuration if all virtual machines were powered on (Choose Two)? A. 1 vNetwork Distributed Switch per Datacenter B. 4 64-bit Windows Passed VCP-410 based vCenter Servers in Linked Mode C. 2 vNetwork Distributed Switches per Datacenter D. 4 32-bit Windows based vCenter Servers in Linked Mode Answer: B, C

o vSphere supports a maximum of eight simultaneous VMotion, cloning, deployment, or Storage VMotion accesses to a single VMFS3 datastore, and a maximum of four simultaneous VMotion, cloning, deployment, or Storage VMotion accesses to a single NFS or VMFS2 datastore. A migration with VMotion involves one access to the datastore. A migration with Storage VMotion involves one access to the source datastore and one access to the destination datastore o Disks are converted VCP-410 exam from thin to thick format or thick to thin format only when they are copied from one datastore to another. If you choose to leave a disk in its original location, the disk format is not converted. o Thin or thick provisioned – not available for RDMs in physical compatibility mode. If you select this option for a virtual compatibility mode RDM, the RDM is converted to a virtual disk. RDMs converted to virtual disks cannot be converted back to RDMs. o You can run the storage vmotion command in either interactive or noninteractive mode. o Interactive mode, type svmotion --interactive. o Noninteractive mode: svmotion [Standard CLI options] --datacenter= --vm ‘:’ [--disks ‘:, :]’ o A snapshot captures the entire state of the VM at the time you take the snapshot. This includes: o Memory state – The contents of the VM’s memory. o Settings state – The VM settings. o Disk state – The state of all the VM’s virtual disks. o Snapshots of raw disks, RDM physical mode disks, and independent disks are not supported. o Change Disk Mode to independent to Exclude Virtual Disks from Snapshots o Persistent – Disks in persistent mode behave like conventional disks on your physical computer. All data written to a disk in persistent mode are written permanently to the disk. o Nonpersistent – Changes are discarded when you power off or reset the VM. Nonpersistent mode enables you to restart the VM with a virtual disk in the same state every time. Changes to the disk are actually written to and read from a redo log file that is deleted when you power off or reset. o Snapshots: o Delete – commits the snapshot data to the parent and removes the selected snapshot. o Delete All – commits all the immediate snapshots before the You are here current state to the base disk and removesall existing snapshots for that VM. o Revert to Snapshot – a shortcut to the parent snapshot of “You are here”. o If you use Active Directory groups for permissions, make sure that they are security groups and not distribution groups. o Users who are currently logged in and are removed from the domain retain their vSphere permissions only until the next validation period (the default is every 24 hours). o A role is a predefined set of privileges. Privileges define basic individual rights required to perform actions and read properties. When you assign a user or group permissions, you pair the user or group with a role and associate that pairing with an inventory object. o Default roles: o System roles – System roles are VCP-410 exam questions permanent. You cannot edit the privileges associated with these roles. o Sample roles – VMware provides sample roles for convenience as guidelines and suggestions. You can modify or remove these roles. o You can also create completely new roles. o All roles permit the user to schedule tasks by default. Users can schedule only tasks they have permission to perform at the time the tasks are created. o Default roles: Role Role Type Description of User Capabilities No Access system Cannot view or change the assigned object. available in ESX/ESXi and vCenter Server. Read Only system View the state and details about the object. available on ESX/ESXi and vCenter Server. Administrator system All privileges for all objects. available in ESX/ESXi and vCenter Server. Virtual Machine Power User sample allow the user to interact with and make hardware changes to VMs, as well as perform snapshot operations. available only on vCenter Server. Virtual Machine User sample allow the user to interact with a VM’s console, insert media, and perform power operations. available only on vCenter Server. Resource Pool Administrator sample allow the user to create child resource pools and modify the configuration of the children, but not to modify the resource configuration of the pool or cluster on which the role was granted. Also allows the user to grant permissions to child resource pools, and assign VMs to the parent or child resource pools. available only on vCenter Server. VMware Consolidated Backup User sample used by the VMware Consolidated Backup product and should not be modified. available only on vCenter Server. Datastore Consumer sample VCP-410 study guide allow the user to consume space on the datastores on which this role is granted. available only on vCenter Server. Network Consumer sample allow the user to assign VMs or hosts to networks available only on vCenter Server.

QUESTION NO: 274 Which of these factors indicates a high likelihood that the performance of a virtual machine is being constrained by disk I/O? A. A large number of kilobytes read and written B. A large number of VCP-410 dumps virtual disks on its SCSI bus C. A large number of disk shares D. A long SCSI queue length Answer: D QUESTION NO: 275 In configuring a VMware HA Cluster the System Administrator can configure Admission Control. There are two options: Prevent VMs from being powered on if they violate availability constraints, or Allow VMs to be powered on even if they violate availability constraints. If the System Administrator chooses the option Prevent VMs from being powered on if they violate availability constraints then which of the following apply in the event of an ESX Host failure (Choose Two)? A. VMware HA enforces the failover capacity defined for the cluster B. Only Virtual Machines with a high restart priority will be restarted on surviving ESX Hosts C. Virtual Machines running on failed ESX Hosts will not be restarted on surviving ESX Hosts D. VMware HA restarts Virtual Machines on surviving hosts with the most unreserved capacity Answer: A,D QUESTION NO: 276 What is the technology VMware Data Recovery uses to back up a Windows 2003 virtual machine? A. Volume Shadow Copy Service B. Crash-consistent quiescing C. LGTO SYNC driver D. EMC Autostart Manager Answer: A QUESTION NO: 271 Which of the following are valid objects to place in a vApp (Choose Three)? A. Folders B. Resource Pools C. Virtual Machines D. vApps E. Hosts Answer: B,C,D QUESTION NO: 272 Recently, a ABC VCP-410 network interface card in an ESX 4 host has been experiencing inconsistent connectivity states. Which of the following two methods could be used to quickly identify the issue and immediately notify an administrator so the issue can be resolved (Choose Two) ? A. Set up an alarm with the Network Redundancy Degraded trigger and configure an SNMP trap for notification when the connection is lost B. Set up an alarm with the Lost Network Connectivity trigger to send an e-mail for notification when The connection is lost C. Set up an alarm with the Lost Network Connectivity trigger and configure an SNMP trap for notification when the connection is lost D. Set up an alarm with the Lost Network Redundancy trigger to send an e-mail for notification when the connection is lost Answer: B,C QUESTION NO: 273 Which of the following features can be used in combination with Network Attached Storage (Choose Three)? A. VMware HA B. Virtual VCP-410 braindump Machine Snapshots C. Raw Device Mapping D. Storage VMotion E. MSCS Clustering Answer: A,B,D

QUESTION NO: 280 When creating a Service Console port, what is the purpose of the gateway device (Choose Two)? A. The gateway device is the network adapter used for the default route. B. A gateway device is always required. C. The gateway device VCP-410 exam questions is the Service Console port used for VMkernel networking. D. A gateway device is required when 2 or more uplinks are using the same subnet. Answer: A,D QUESTION NO: 281 Which of the following would prevent the application of a Host Profile to an ESX Host (Choose Two)? A. The host has not been placed into Maintenance Mode B. The host is an ESX 3.5 Host C. The host has multiple profiles attached D. The host is an ESXi Host Answer: A,B QUESTION NO: 282 An ESX Server in a DRS cluster is placed into Maintenance Mode. Which of the following conditions are true (Choose Two)? A. If the DRS cluster is in fully automated mode, DRS will make a migration recommendation and then VMotion Virtual Machines to other ESX servers B. If the DRS cluster is in partially automated mode then the Virtual Machines that have a High Restart Priority will be moved to another ESX Server C. If the DRS cluster is in partially automated mode then the vCenter Administrator must VMotion Virtual Machines to another ESX Server D. If the DRS cluster is in fully automated mode, DRS will automatically VMotion Virtual Machines to other ESX Servers Answer: C,D QUESTION NO: 277 The Runtime Name for a Fibre Channel storage device is equivalent to? A. The Universally Unique Identifier (UUID) to the device B. The name of the current path to the device in vmhba:C:T:L format C. The name of the first discovered path to the device in vmhba:C:T:L format D. The Network Address Authority (NAA) name of the device Answer: C QUESTION NO: 278 In the vSphere Client the VCP-410 study guide Virtual Machine Resource Allocation tab shows Host Memory and Guest Memory. What is the meaning of these terms? (Choose Two)? A. Host memory is the actual memory usage of the Virtual Machine. B. Guest Memory is the actual memory usage of the Virtual Machine C. Host memory is the amount of physical memory that has been allocated to a Virtual Machine D. Guest Memory is amount of physical memory that has been allocated to a Virtual Machine Answer: B,C QUESTION NO: 279 Which of the following occurs if VMware Fault Tolerance is enabled for a virtual machine in a DRS/HA cluster, but Host Monitoring is not enabled for VMware HA? A. If the primary FT VM fails, the secondary FT VM does not take over B. Memory reservations for the FT VM cannot be upheld and there might not be sufficient resources to restore redundancy if an HA event occurs C. If the primary FT VM fails, a new secondary FT VM is not created and the VM is no longer redundant D. Anti-affinity rules for the VCP-410 questions FT VM cannot be upheld and both the primary and secondary FT VM could reside on the same host Answer: C

QUESTION NO: 286
Which of the following options cannot be edited if vApp Options is disabled in the
Options tab for a Virtual <a href="http://www.certifyme.com/VCP-410.htm">VCP-410</a> Machine that is part of a vApp (Choose Two)?
A. vApp Resources
B. IP Allocation Policy
C. vApp Startup and Shutdown Options
D. OVF Environment Transport
Answer: B,D
QUESTION NO: 287
Which of the following two options cannot be edited if Appliance Options
are disabled (Choose Two)?
A. License Agreement
B. Resources
C. Properties
D. Startup and Shutdown
Answer: A,C
QUESTION NO: 288
Which vCenter Server role, by default, has performance privileges?
A. Virtual Machine Power User
B. Virtual Machine Administrator
C. Resource Pool Administrator
D. Datacenter Administrator
Answer: B


QUESTION NO: 283
Which pre-defined vCenter <a href="http://www.certifyme.com/VCP-410.htm">VCP-410 braindump</a> Server role can assign permissions to users?
A. Datacenter Administrator
B. Virtual Machine Power User
C. Administrator
D. Resource Pool Administrator
Answer: C
QUESTION NO: 284
ESX Service Console user authentication (Choose Two)?
A. can use a central directory service for password checking only
B. requires local accounts
C. requires users to change their passwords every 6 months by default
D. controls vCenter authentication for vSphere Client users
Answer: A,B
QUESTION NO: 285
An administrator wants to enable Guest Customization in vCenter Server for various
Windows and Linux virtual machines. Which of the following steps must be performed
on the vCenter Server and in the guest virtual machines (Choose Two)?
A. Microsoft Sysprep tools must be placed on the vCenter Server
B. Perl must be installed in the Linux guest OS
C. The Linux Open <a href="http://www.certifyme.com/VCP-410.htm">VCP-410 exam</a> Source tools must be added to the vCenter Server
D. The Windows guest OS must be Windows NT4, 2000, 2003 or 2008
Answer: A,B